Get in touch

In Auckland, and need a quote? Get in touch today.

Contact Us →

Gasfitting Services Auckland

Need gas heating installed or gas appliances fitted in Auckland? Our certified gas fitters handle all your heating and gas installation needs safely.

Get in touch

In Auckland, and need a quote? Get in touch today.

Contact Us →

No Hot Water at Home? What to Check Before You Call a Plumber

TL;DR

If you have no hot water, first check whether it is every tap or just one, and whether the power to the cylinder is on. If the cylinder has no power, is leaking, or the problem is still there after your checks, call a plumber. This guide covers a standard storage hot water cylinder.

Key Takeaways

  • Check whether the problem is every hot tap or just one.
  • Look at the switchboard to see if the cylinder has lost power.
  • Look around the cylinder for water. A leak means turn it off and call a plumber.
  • Do not open electrical covers or keep resetting a switch that keeps tripping.
  • If the checks do not fix it, the element, thermostat or cylinder may need attention.

No hot water is one of the most disruptive problems in a home. There is nothing like a cold shower to start a bad day. When the hot water stops, it is natural to wonder whether it is a quick fix or a big job. A few simple checks can often tell you which.

In this post, you’ll learn what to check first, what not to touch and when to call a plumber. It covers a standard storage cylinder, which is the tank most homes keep in a hot water cupboard.

Is it every tap or just one?

Run the hot water at a few taps, such as the kitchen, the bathroom and the shower. If only one tap runs cold or the flow is weak, the problem is probably that tap or its mixer, not your cylinder. If every hot tap runs cold, the problem is likely with the cylinder or its power supply.

Also notice whether the water is completely cold or just not as hot as usual. Water that is lukewarm, or that runs out far faster than it used to, often points to a worn heating element or thermostat. That is a fault a plumber can usually diagnose quickly.

Check the power and look around the cylinder

Most electric cylinders are on their own switch or circuit at the switchboard. Check that it has not tripped. If you switch it back on and it works, keep an eye on it. If the switch trips again straight away, leave it off. A switch that keeps tripping is telling you there is a fault, and repeated resetting is not safe.

Then look at the cylinder and the floor around it. Dampness, drips or a puddle mean the cylinder or its connections are leaking. If you see water, switch off the power to the cylinder and close the valve on the cold water supply to it if you can reach it safely. Do not touch anything electrical if the area is wet. Our guide to a leaking hot water cylinder explains what to do next.

Do not remove electrical covers or panels yourself. If the fault turns out to be in your switchboard or wiring rather than the cylinder, you will need an electrician. A plumber can help you work out which it is.

When to call a plumber

Call a plumber if the power is on and you still have no hot water, if the water has gone rusty or smelly, if there is any leak around the cylinder, or if you can hear unusual banging or hissing. If you are unsure, call anyway. We would rather you ask than guess.

The fix might be as simple as replacing a part. If the cylinder itself has failed, we will tell you honestly and explain your options. Our hot water cylinders page covers both repairs and replacements, and our plumbing services page lists the rest of what we do.

Why a cylinder stops heating

There are a few usual suspects. The heating element can wear out, the thermostat can fail, the power supply to the cylinder can be interrupted, or the cylinder itself can fail. A plumber can test these in a sensible order, which is quicker than guessing. If you know roughly how old your cylinder is, tell us, because age helps us judge whether a repair makes sense.

What to tell your plumber

Tell us when the hot water stopped, whether it is every tap or just one, whether the cylinder switch has tripped, and whether you have seen any water, rust or noises. If you can, send a photo of the cylinder label. It often shows the model and the size, and that saves time.

While you wait, you can heat water in the kettle for basic needs. If the cylinder is leaking, do not keep using it.

Get your hot water back

Grace Plumbing looks after homes in Ellerslie, Mount Wellington, Remuera and Mission Bay. Call 09 525 5733 and tell us what you have checked so far. That helps us get to the cause faster. Grace Plumbing is open Monday to Friday, 7:30am to 4:30pm. Residential work is backed by the $20,000 Master Plumbers Guarantee. See the areas we serve.

Related reading

Grace Plumbing - Plumbing Solutions and Services

Quick links

Based on 500+ Reviews

☆☆☆☆☆ (4.9/5)

★★★★★
The team at Grace were flexible and were able to slot in my job at ...
Read More
Kevin Sherlock
★★★★★
The team at Grace were flexible and were able to slot in my job at short notice. Great communication throughout
★★★★★
Awesome experience with the team at Grace Plumbing from start to finish. Great communication
Tommy
★★★★★
Awesome experience with the team at Grace Plumbing from start to finish. Great communication
★★★★★
Ryan carried out the work and was friendly, efficient, and highly professional.
Taki Smart
★★★★★
Ryan carried out the work and was friendly, efficient, and highly professional.
★★★★★
The customer services person on the phone was fantastic - very helpful and understanding.
Mark Warden
★★★★★
The customer services person on the phone was fantastic - very helpful and understanding.
Secret Link